NAESA EASTERN REGION WORKSHOP
Why
Code Data Plates
by: John S. Rearick
CodeDataPlate.com
CodeDataPlate.com
INTRODUCTION
• HISTORY
– First Introduced in 1996 Edition
– Special Section in 2000 Edition (8.9)
• TEN YEARS OF PRACTICE
– Learning Curve
– Problems Encountered
CodeDataPlate.com
SECTION 8.9
Requirement 8.9 contains requirements for all new and existing
equipment within the Scope of this Code.
8.9.1 Required Information
Data plate shall be provided and maintained that shall indicate the
Code to be used for inspections and tests (see 8.10.1.2). The data plate
shall indicate the Code and edition in effect at the time of installation.
CODE DATA PLATE
INSTALLATION CODE:
ASME A17.1a-1997
codedataplate.com
The data plate shall also indicate the Code in effect at the time of
any alteration
ALTERATION CODE:
ASME A17.1a-2005
and indicate the applicable requirements of 8.7.
SECT. 8.7 REQUIREMENTS COMPLIED WITH:
#REF!
8.7.2.11.5, 8.7.3.8, 8.7.3.24, 8.7.3.29, 8.7.3.30,
8.7.3.31.2, 8.7.3.31.5, 8.7.3.31.8
CodeDataPlate.com
8.7.3.31.1,
codedataplate.com
Edition Sensitive Items
(85 years of code)
•
•
•
•
•
•
•
•
•
•
A17.3 applies from d-1986 through d-2000 to Part XII
Item 1.6 Car Emergency Signal there are 6 differences
Space Guards A17.1-1937 and later editions (also A17.3)
Static Control a-1988 and later editions
Glazing b-1989 and later editions & again in a-2005
Item 1.12/13 & 3.8 (Cab items) there are 16 differences
and 16 more relating to car & hoistway doors & gates
Door Restrictors b-1980, b-1983 and b-1989 differences
Hydro RPR required for installations under c-1986 and later
Fire Service b-1973, 1981, 1984, b-1989 and 2000
CodeDataPlate.com
CDP Flow Chart
START
Determine the Original
Maufacturer and serial
number of the base
equipment.
Determine date of
Manufacture from
Cross Head Data
Plate
No
Have there been
Alterations?
No
Contacted
Manufacturer to obtain
the Installation Code
Yes
Determined building
construction period estimate elevator
install permit date
Yes
Yes
Yes
No
Subtract time from permit
to manufacture (6-18
months)
Determine the
Modernization
Installer and Date
Determine code in effect
from AHJ for the estimated
permit date
Determine scope of alterations and the
applicable alteration rules and the
applicable alteration code edition
FINISH
Order Proper
Code Data Plate
CodeDataPlate.com
Install Code Data
Plate on Controller or
Main Line Disconnect
STANDARD PLATES
IN STOCK
• CODE YEARS 1921 TO PRESENT
CO DE DATA PLATE
IN S T A L L A T IO N C O D E :
A S M E A 1 7 .1 -2 0 0 7
c o d e d a ta p la te .c o m
CODE DATA PLATE
IN S T A L L A T IO N C O D E :
A N S I/A S M E A 17.1a-1985
c odedataplate.c om
CODE DATA PLATE
IN S T A L L A T IO N C O D E :
ASA
A 17.1-1965
c odedataplate.c om
CodeDataPlate.com
Reading the Plate
Door Operator
Plunger Gripper
C O D E D ATA PLATE
Wiring
IN S T A L L A T IO N C O D E :
Re-opening
Devise
Door Restrictor
A L T E R A T IO N C O D E :
B u lle tin 1 1 0
A S M E A 1 7 .1 -2 0 0 4
S E C T . 8 .7 R E Q U IR E M E N T S C O M P L IE D W IT H :
#R EF!
8.7.2.11.5, 8.7.2.13, 8.7.3.8, 8.7.3.12, 8.7.3.23.7, 8.7.3.24,
8.7.3.30, 8.7.3.31.1, 8.7.3.31.2, 8.7.3.31.5, 8.7.3.31.8
8.7.3.29,
co d e d a ta p la te .co m
Limits
Controller Replacement
Top of Car Insp..
Emergency Operations
Leveling
CodeDataPlate.com
Valve
Pump Unit
Tank
CodeDataPlate.com
CodeDataPlate.com
Job Information
Web, e-mail, phone or fax
C o d e D ata P late O rd er F o rm
M o d e rn iza tio n Ite m s - ch e ck th o se th a t a p p ly a n d p ro v id e a d d itio n a l in b la n ks:
A lteration to H oistw ay:
A scending C ar/unintended M ovem ent P rotection
H oistw ay V entilation
C hange in N um ber of R opes
M ach. R oom A ccess:
A ddition of R ope E qualizers
M ach. R m . A lteration:
A ddition of A uxiliary R ope-F astening D evices
R eplace or alter W iring
A lteration to cw t:
H orizontal S lide E ntrance(s) added
Installation of or A lteration to C w t. R oller G uides
V ertical B i-P arting E ntrance(s)
A lteration to C ar or C w t. B uffers or B um pers
T racks and/or H angers R eplaced
A lteration of G uide R ails, S upports and F astenings
Interlocks R eplaced
A lteration to M achine, M otor or S heaves
H W A ccess and/or U nlocking D evice A lteration
C hange in location of D riving M achine
D oor restrictors added
A lteration to T erm inal-S topping D evices
D oor O perator added or altered
A ddition of or alteration to T op of C ar O perating D evice
D oor R e-O pening devise added or altered
A ddition of or alteration to C ar leveling or T ruck-Z oning D evice
C om plete N ew C ab
C hange of M ain P ow er S upply
R em odel E xisting C ab:
C ontroller change
A lteration of C ar F ram e or P latform
C hange in T ype of M otion C ontrol (A C , D C , V V , S C R , etc.)
Installation of or A lteration to C ar R oller G uides
C hange in T ype of O peration C ontrol (C ar S w ., A utom atic, etc.)
Increase/D ecease D eadw eight of C ar m ore than 5%
C harge to E m ergency O perations or S ignaling devices
C hange in T ype of S ervice
Installation of new H ydraulic Jack
C hange in C lass of Loading
Install or alter P lunger
C hange to carry P assengers on F reight elevator
Install, alter or sleeve C ylinder
Increase in R ated Load
Increase W orking P ressure
Increase or D ecrease T ravel
C hange location of H ydro Jack
Increase in R ated S peed
R elocation of H ydraulic M achine to below top of C ylinder
D ecrease in R ated S peed
Installation of P lunger G ripper
R eplace or install N ew C ar S afety
C hange to V alves, P ressure P iping & F ittings
R eplace or install N ew C w t. S afety
Install or alter T ank
A lter E xisting C ar or C w t. S afety
A lter A nti-C reep Leveling device
A lter or install N ew S peed G overnor
Install or alter E m ergency Low ering
O th e r ite m s m o d e rn ize d , co m m e n ts o r a n y a d d itio n a l In fo rm a tio n :_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _CodeDataPlate.com
_______________________________________________
CodeEdition
ASME A17.1a-2005
ASME A17.1-2000
ASME A17.1b-1998
ASME A17.1b-1995
ASME A17.1b-1992
ASME A17.1a-1991
ASME A17.1-1990
ASME/ANSI A17.1b-1989
ASME/ANSI A17.1a-1988
ASME/ANSI A17.1-1987
ANSI/ASME A17.1e-1987
ANSI/ASME A17.1c-1986
ANSI/ASME A17.1b-1985
ANSI/ASME A17.1-1984
ANSI/ASME A17.1b-1983
ANSI/ASME A17.1a-1982
ANSI/ASME A17.1-1981
ANSI A17.1b-1980
ANSI A17.1a-1979
ANSI A17.1-1978
ANSI A17.1g-1976
ANSI A17.1f-1975
ANSI A17.1c-1974
ANSI A17.1b-1973
ANSI A17.1a-1972
ANSI A17.1-1971
ANSI A17.1d-1970
USAS A17.1b-1968
USAS A17.1a-1967
ASA A17.1-1965
StartDate
EndDate
December 8, 2006
October 1, 2005
October 4, 2000
August 1, 1996
February 2, 1994
August 29, 1992
August 9, 1991
May 31, 1990
May 16, 1989
November 1, 1988
November 1, 1987
October 31, 1986
July 1, 1986
July 1, 1985
September 19, 1984
July 1, 1983
July 1, 1982
September 1, 1980
July 1, 1979
October 1, 1978
December 1, 1976
November 1, 1975
May 1, 1974
November 1, 1973
March 1, 1972
January 1, 1972
July 1, 1971
January 1, 1970
January 18, 1968
April 1, 1966
December 7, 2006
September 30, 2005
October 3, 2000
July 31, 1996
February 1, 1994
August 28, 1992
August 8, 1991
May 30, 1990
May 15, 1989
October 31, 1988
October 31, 1987
October 30, 1986
June 30, 1986
June 30, 1985
September 18, 1984
June 30, 1983
June 30, 1982
August 31, 1980
June 30, 1979
September 30, 1978
November 30, 1976
October 31, 1975
April 30, 1974
October 31, 1973
February 29, 1972
December 31, 1971
June 30, 1971
December 31, 1969
January 17, 1968
Florida
Data Base of Effective Dates
Serial Number
92918
89682
59628
51752
47694
46588
45796
44573
43255
42310
41099
39637
39414
37812
36387
34073
32996
30297
28921
27033
24572
24016
22172
20916
10205
9982
9296
7521
4420
43 AHJ’s
CodeEdition
Type
StartDate
EndDate
ASME A17.1b-2003
ASME A17.1a-1997
ASME/ANSI A17.1b-1989
ANSI/ASME A17.1a-1985
ANSI/ASME A17.1a-1982
ANSI A17.1b-1980
ANSI A17.1-1978
USAS A17.1a-1967
ASA A17.1-1965
NYC BC 1938 - Article 14
NYC BC 1931 - Article 27
NYC BC 1922 - Article 27
NYC BC 1915 - Article 27
2
2
2
2
2
2
2
2
2
2
2
2
2
July 1, 2008
April 17, 2003
January 1, 1991
January 1, 1987
January 1, 1985
January 1, 1981
January 1, 1979
January 1, 1970
January 1, 1968
January 1, 1938
January 1, 1931
January 1, 1922
January 1, 1915
January 1, 2018
June 30, 2008
April 16, 2003
December 31, 1990
December 31, 1986
December 31, 1984
December 31, 1980
December 31, 1978
December 31, 1969
December 31, 1967
December 31, 1937
December 31, 1930
December 31, 1921
CodeDataPlate.com
N.Y.C.
Custom Software
CodeDataPlate.com
Custom
Software
CodeDataPlate.com
Other Types of Plates
• Job Specific Plates
• ADJ Specific Plates
– NYC
– Mass.
– Penn.
- Ohio
- Calif.
- MO
• Add on Plates
• Cross-head Plates
• T/H plates
CodeDataPlate.com
-Iowa
-WA
-A17.3
CROSSHEAD DATA PLATE TEMPLATE - HY
For use for Hydralic elevators installed under A17.1b-1995 and earlier editions
●
●
Under b-1995 and earlier
CROSSHEAD DATA PLATE
COMPLETE CAR WEIGHT:
Hydro
POUNDS
RATED LOAD:
F.P.M.
RATED SPEED:
MANUFACTURED:
BY:
Under 1996 CROSSHEAD
and later
DATA● PLATE TEMPLATE - HY
●
Note: Approximate Plate size is 7" x 2.75" with .125" lettering.
●
●
CROSSHEAD DATA PLATE
QUANTITY
COMPLETE CAR WEIGHT:
1
4 HOLES X
DOUBLE FACED TAPE
POUNDS
CAR #'s
PLUNGER WEIGHT:
Other
Products
POUNDS
APPROVED
RATED LOAD:
DOWN SPEED:
F.P.M.
DATED
P.O. #
BY:
MANUFACTURED:
RAIL LUBRICATION INSTRUCTIONS:
Work order #
●
X
1106-02
●
CROSSHEAD DATA PLATE TEMPLATE
- TR
A17.1-1990 Rule 301.10 = speed is down direction and is not to include weight of plunger
this seems to be a clarification - the referance is still back to Section 207
●
●
CROSSHEAD DATA PLATE
COMPLETE CAR WEIGHT:
Replacement
Crosshead
Plates
RATED LOAD:
POUNDS
POUNDS
RATED SPEED:
NUMBER OF ROPES:
DIAMETER:
RATED BREAKING STRENGTH:
MANUFACTURED:
F.P.M.
IN.
POUNDS
BY:
RAIL LUBRICATION INSTRUCTIONS:
the safety
for the characteristics of the rail lubricant to be used.
CodeDataPlate.com
●
●
Other Products
T E M P E R A T U R E -H U M ID IT Y D A T A P L A T E T E M P L A T E - S T A N D A R D
R e q u ire m e n t 2 .7 .5 .2 ( 2 .7 .9 .2 in A 1 7 .1 -2 0 0 7 )
N E II-1 R a n g e s s h o w n w h ic h is tig h te r th a n m o s t m a n u fa c tu re s '
C u s to m ra n g e s a va ila b le o n s p e c ia l o rd e r
A m b ie n t A ir R e q u ire m e n ts
T e m p e ra tu re
o
o
1 3 C (5 5 F )
R e la tive H u m id ity
80%
M in .
o
o
3 2 C (9 0 F )
M ax.
M ax.
c o d e d a ta p la te .c o m
N o te : Ap p ro x im a te P la te s iz e is 5 .5 " x 1 .5 " w ith .1 2 5 " le tte rin g .
2 .7 .9 .2 T e m p e ra tu re a n d H u m id ity. M ach in ery
sp aces, m ach in e ro o m s, co n tro l sp aces, and co n tro l
ro o m s sh all b e p ro vid ed w ith n atu ral o r m ech an ical
m ean s to keep th e am b ien t air tem p eratu re an d h u m id ity
in th e ran ge sp ecified b y th e elev ato r eq u ip m en t
m an u factu rer to en su re safe and no rm al o p eratio n of
th e elevato r. T h e tem p eratu re an d h u m id ity ran ge sh all
b e p erm an en tly p o sted in th e m ach in e roo m , co n tro l
ro o m , co n tro l sp ace, o r w h ere sp ecified b y th e eq u ip m en t
m an u factu rer, in th e m
ach in ery sp ace.
CodeDataPlate.com
Code Data Plate Kit
Other
Products
O H IO S 1 (R e d B o o k )
O H IO S 1 1
B u lle tin 1 1 0
A S M E A 1 7 .1 a -1 9 9 4
B e fo re 4 /1 /7 4
7 /1 /9 5 to 7 /3 1 /9 6
O H IO S 2
O H IO S 1 2
A N S I A 1 7 .1 b -1 9 7 3
A S M E A 1 7 .1 b -1 9 9 5
4 /1 /7 4 to 9 /9 /7 9
8 /1 /9 6 to 3 /3 1 /9 9
O H IO S 3
O H IO S 1 3
A N S I A 1 7 .1 a -1 9 7 9
A S M E A 1 7 .1 a -1 9 9 7
9 /1 0 /7 9 to 8 /1 4 /8 0
4 /1 /9 9 to 8 /1 9 /9 9
CodeDataPlate.com
8.7.2.18
Safeties
8.7.3.15
For complete list see A17.1 Sect. 8.7 & App. L
TRACTION
8.7.2.19
8.7.2.20
Code Data Plate (8.6.1.5)
Alteration Pocket Guide
8.7.1
General Requirements
TRACTION
HYDRO
8.7.2
8.7.3
8.7.2.1
Hoistway
8.7.3.1
8.7.2.2
Pits
8.7.3.2
8.7.2.7
Machine room
8.7.3.7
8.7.2.8
Wiring
8.7.3.8
8.7.2.10
Entrances
8.7.3.10
8.7.2.10.1 General
<<<<
8.7.2.10.2 Horizontal Slide
<<<<
8.7.2.10.3 Vertical Slide
<<<<
8.7.2.10.4 Swing Type
<<<<
8.7.2.11
Hoistway Door
8.7.3.11
8.7.2.11.1 Interlocks
<<<<
8.7.2.11.4 Access Sw. (App. R)
<<<<
8.7.2.11.5 Door Restrictor
<<<<
8.7.2.12
Operators
8.7.3.12
8.7.2.13
Re-opening Device
<<<<
8.7.2.14
Cabs
8.7.3.13
8.7.2.14.1 New Cab
<<<<
8.7.2.14.2 Cab Alt. Except panels
<<<<
8.7.2.14.3 Cab Alt. Interiors only
<<<<
8.7.2.14.5 Remove Stop Switch (before b-2003)
8.7.2.15
Frame, Plat. & Guides
8.7.3.14
8.7.2.16
Load and Class
8.7.2.16.1 Type of Service
8.7.3.17
8.7.2.16.2 Class of Loading
8.7.3.18
8.7.2.16.3 Pass on Freight
8.7.3.19
8.7.2.16.4 Increase Rated Load
8.7.3.20
8.7.2.17
Travel or Speed
8.7.3.22
8.7.2.18
Safeties
8.7.3.15
For complete list see A17.1 Sect. 8.7 & App. L
TRACTION
8.7.2.19
8.7.2.20
Governor
Rope Brake, etc.
Hydraulic Jack
Hydraulic Cylinder only
Move Power Unit
Plunger Gripper
HYDRO
Governor
8.7.3.16
Rope Brake, etc.
Hydraulic Jack
8.7.3.23.1
Hydraulic Cylinder only
8.7.3.23.3
Move Power Unit
8.7.3.23.6
Plunger Gripper
8.7.3.23.7
Valve & Piping
8.7.3.24
8.7.2.21
Ropes
8.7.3.25
8.7.2.22
Counterweights
8.7.3.26
8.7.2.22.3 Cwt. Guides
<<<<
8.7.2.23
Buffers
8.7.3.27
8.7.2.24
Rails
8.7.3.28
Tank
8.7.3.29
8.7.2.25
Machines
8.7.2.26
Terminal Stopping
8.7.3.30
8.7.2.27
Control Equipment
8.7.3.31
8.7.2.27.1 Top of Car
8.7.3.31.1
8.7.2.27.2 Leveling
8.7.3.31.2
Anti-Creep
8.7.3.31.3
8.7.2.27.3 Power Supply
8.7.3.31.4
8.7.2.27.4 Controller
8.7.3.31.5
8.7.2.27.5 Type of Motion
8.7.3.31.6
8.7.2.27.6 Type of Operation
8.7.3.31.7
Emergency Lowering
8.7.3.31.9
8.7.2.27.7 Remove Stop Switch*
8.7.3.31.10
8.7.2.28
Emerg. Operations
8.7.3.31.8
8.7.4
Other Driving Machines
8.7.5
Special Applications
8.7.6
Escalators & MW
8.7.7
Dumbwaiters & ML
*A17.1b-2003 and later editions only
HYDRO
8.7.3.16
Pocket Code
8.7.3.23.1
CodeDataPlate.com
8.7.3.23.3
8.7.3.23.6
8.7.3.23.7
CodeDataPlate.com
281/257-0516
Other Products
Now
Available
CodeDataPlate.com
New Inspection Tags - 8.11.1.6
Courtesy of Zack McCain
Now
Available
CodeDataPlate.com
Now Available
CODE DATA PLATE
ALTERATION CODE: ASME A17.1
b-2003
-2004
a-2005
-2000
a-2002
-2007
SECT. 8.7 REQUIREMENTS COMPLIED WITH:
#REF!
8.7.2.11.5
8.7.2.13
8.7.2.14
8.7.2.20
8.7.2.28
8.7.3.13
8.7.3.23.1
8.7.3.24
8.7.3.31.8
8.7.3.31.9
cdp
Field Marked Alteration Plate
Covers common alterations
CodeDataPlate.com
Under Development
C O D E D ATA PLATE
IN S T A L L A T IO N C O D E :
A S M E A 1 7 .1 -2 0 0 7
E X C E P T F O R S E C T IO N S :
2 .X .X , 2 .Y .Y , 2 .Z .Z
T h is e le va to r c o m p lie s w ith A S M E A 1 7 .7 /C S A B 4 4 .7
S# eReE FM! a in te n a n c e C o n tro l P ro g ra m
c o d e d a ta p la te .c o m
Section 2.11 of A17.7
CodeDataPlate.com
Other Issues
• Magic Marker Plates
• Foil Plates
• Mounting Locations
– External Plate for Escalators - 2007 code
• TN 07-1083
– Securely fastened
– Permanently legible
• Durable mean to prevent loss of data or
• Raised or depressed .8 mm (.03125 in)
– Rationale: Assure information is available for life of equipment
CodeDataPlate.com
Conforming Plates
“T h e re fo re, fo r o u r p u rp os es h e re in th e ” A H J of _ __ _ _ _, “in th e
in te res t of u nifo rm ity a n d c o ns iste nc y th ro u g h ou t th e s tate, th e
fo llo w in g a re th e offic ia l p o lic ies re g a rd in g c o d e d a ta p lates :
1 . C o d e d ata p la tes s ha ll be e ith e r m e tal o r p las tic.
2 . C o m p ute r o r typ e w rite r p rin ted la be ls a re p ro h ibite d.
3 . T yp e w ritte n o r h a n d w ritte n fig u res o r lette rin g a re n ot ac ce p tab le .
4 . W ritin g th e c o d e info rm a tio n w ith a p e rm a ne n t m a rk e r on to a
c o n tro lle r c o ve r o r d is c on n e ctin g m e a n s c o ve r is n ot acc e pta b le.”
CodeDataPlate.com
Discussion
• As Inspectors what are you seeing?
– What percent of units have proper information?
– Is it on a compliant plate?
• What can we do to offer a better product?
– What is Helpful?
– What is not?
CodeDataPlate.com
Thank You
CodeDataPlate.com
Descargar

No Slide Title